Andreas Taylor

TI_Platform_Cores_For_Arduino. Use Arduino as a replacement for Energia to develop on Texas Instruments LaunchPad products in the MSP430, MSP432, and Tiva families.

AY3891x. Platform-independent Arduino library for General Instrument AY-3-8910 / AY-3-8912 Programmable Sound Generator chip and its clones (YM2149, YM3439, T7766A, among others).

PiMac. The "PiMac" -- converting a 2005 iMac G5 into a Raspberry Pi desktop.

TLC591x. Library for Texas Instruments TLC5916 and TLC5917 constant current LED sink driver for Arduino.

HCMS39xx. Arduino library to interface with Broadcom/Avago HCMS-39xx and HCMS-29xx series LED displays.

SWI2C. Software I2C interface library for Arduino. Does not use any platform-specific code, and has a much simpler API than standard Wire library.

emulator-8-bit. CPU emulator and disassembler for 8-bit processors. Currently supports Z80 and my Homemade CPU.

FutabaVFD162S. Improved version of the FutabaUsVfd library published on Arduino Playground. The library is designed to work with the Futaba 162SD03C Vacuum Fluorescent Display, and may work with other VFDs using the same controller chips.

ICM7218. Library to interface with Intersil/Renesas and Maxim ICM7218 and Intersil/Renesas ICM7228 LED driver chips. Compatible with Arduino and Energia.

matrix-keypad-library. Simple-to-use matrix keypad library.

NewhavenOLED. Arduino library for Newhaven OLED displays using US2066 controller chip. Bit-bang SPI implementation allows selection of any I/O pins to control the display.

Noritake-GU7000. Noritake GU7000 Vacuum Fluorescent Display (VFD)

TI-30-Keypad-Interface. Hardware interface information and Arduino sketch to simulate the keypad of the original bubble-lens LED TI-30 calculator.

MSP430TempSensorWithDisplay. Wireless temperature sensor which uses an MSP-EXP430FR2433 LaunchPad, 430BOOST-CC110L wireless transceiver, BOOSTXL-BATTPACK LiPo power source, and 430BOOST-SHARP96 low-power display.

MspTandV. Calculates calibrated chip temperature and Vcc voltage using factory calibration values stored in chip TLV structure in MSP430 controllers. Vcc measurement is useful for battery-operated operation to determine when the battery is running low. Also calculates calibrated ADC values when using the chip's internal voltage reference.

Kentec_35_Parallel. Library to support the Kentec EB-LM4F120-L35 3.5" QVGA TFT LCD BoosterPack with Parallel I/O.

BQ27441_SWI2C. This library interfaces with the Texas Instruments BQ27441 Battery Fuel Gauge using software I2C. This allows the device to be connected to any two available I/O pins instead of the hardware-specific I2C peripheral pins.

EEPROM_24C08_SWI2C. Library to interface with the 24C08 external I2C 8Kx1 EEPROM using a software I2C implementation, and can therefore use any 2 I/O pins for interfacing with the EEPROM.

Outdoor-Weather-Sensor. Outdoor wireless weather sensor based on TI MSP-EXP430G2 LaunchPad, SENSORHUB BoosterPack and CC110L BoosterPack. Optimized for low-power operation, 2xAA cells should be able to power the device for well over a year.

Windows10-on-iMac2011. Install Windows 10 on 2011 iMac using Boot Camp. Also includes tips for replacing the HDD with an SSD.

ParallelEEPROM. Parallel EEPROM programmer library. The library currently supports 32Kx8 (28C256 and X28256) and 2Kx8 (28C16) EEPROMs. Other sizes may be supported in the future.

retro-calculator. Simple retro calculator using NSA1166 bubble LED display.

GPS-Breakout-with-LCD. GPS Receiver setup using Tiva TM4C LaunchPad, SparkFun ZOE-M8Q GPS breakout, and CrystalFonz 8x2 LCD.

Energia-EducationalBP_MKII. Educational BoosterPack MkII examples from Energia application packaged as a library so they can be loaded into Arduino.

ESP-WiFi-DS18B20-Temp-Sensor. ESP8266-based WiFi temperature monitor using two DS18B20 1-Wire sensors.

HapTouch. Library for an I2C command interface to the HapTouch BoosterPack.

BoydPrinter. Arduino library designed to control the Seiko MTP-120 thermal printer that is part of the "Boyd Dimension Calculator." It will only work with a modified version of the calculator as described in the README file.

USB_Host_ASCII_Keyboard. Converts USB keyboard into plain ASCII over Arduino Serial port using USB Host Shield.